lundi 8 avril 2013

Tutorial: Fimo hollow beads

en français ici

Tutorial: Fimo hollow beads
par Florence

The trick which allowed me to realise this creation, was learnt during Chritine Dumont atelier, an artist I admire so much.
this is the tutorial:
61800320
61798680

Take the polymer clay in whichever color and brand you prefer, and a paper ball (in French: cotillon, the one you throw with joy on the head of your friends during parties)
61800845   
61800833
You cut a square of clay (passed at the largest set on the pasta machine). The square must be large enough to cover the paper ball. Refold the corners on the ball and cut the exceeding clay with a cutter. Then, mend the edges (with the fingers or a small roller) in order to cancel the connections traces.
61800943
    
this will result in a bead well rounded and smooth. You will put it in the oven and bake it, following the precise instructions of the chosen brand.

61801219

After that, put an end piece cylinder-shaped on your electric drill and pierce four big holes on the four poles of the ball. Make sure your end piece is well at a right angle on the bead and that you keep it steady during the making (this will avoid to see UFO flying during the process).




    61801194

When you will have made four big holes on the bead, you take a finer end piece cylinder-shaped ancd you make some other smaller holes. But not too much, in order not to make the bead too fragile. (I know, it is not easy to slow down at this stage, but you will make it!). After that, you plunge your bead in the cold water and you let it simmer for about half an hour.

Using a crochet rod, similar to the one used for crustaceans, remove very carefully, little piece by little piece, the scraps of the cotillon.
   61801377 

61801365

Une fois cette opération faite, changez votre embout de perceuse pour des forets de tailles différentes et lâchez-vous.  Faite tous les trous que vous voulez pour que votre perle soit harmonieuse sans trop les rapprocher pour que la perle reste solide.

This operation done, you can change the end piece on your electric drill using the sizes you prefer and you start amusing yourself. You can do all the holes you like to, trying to harmonize your bead and not to have holes too close one to another, otherwise your bead will be too fragile.

And this is it!!!

61801709

Isn't it simple? This was also created by a designer I didn't know, and that I've just discovered:
Einat

-----------------------------------------------------------------------------------

The story goes on...

When two polymer friends take up a challenge, is is possible to resist?

Genviève, alias Jancydol, seeing my bead, challenged me to create a bead within the bead. And thanks to a little trick from another friend, Marie-Christine, alias MCBE Créations, I could rise to this irresistible challenge! LOL

61544891_p

Marie Christine's trick

My trick consists in using some toilet paper or kitchen roll to make a bead. If you want to use it to lighten a polymer bead (not with holes), you can add some white glue mixed to water to the paper, and let it dry before you recover it.

If, like Florence, you want to take away the paper when the bead is baked, you do not have to mix glue or use a cotillon bead instead. After thinking about this trick, Florence and I had the same idea: to make a bead in a cage.

This is my way:
You will need:

-a bead or a ball (better if it is not pierced) around 1,5 cm or more little.
- 2 to 3 polymer clay bars (here Fimo), in colors which match the bead
- a clay gun (it will make the processus more rapid) with a rectangle end piece
- 3 to 4 sheets of toilet paper
- a little bowl of water

61816706

Tear the toilet paper in strips (1 cm large)

61816849
Start to enwrap the bead with the paper, moistening it with a finger (but not soaking the paper in the water)

61816961

61816984

Roll the bead in your hands, in order to mix well the paper: you will obtain a good ball, which will leave 2-3 mm between the bead and the cage.


61820274
Let it dry. If it is still damp, don't worry, bec ause the bead will not be completely covered and the dampness will evaporate during the baking.
Condition the clay, form a log and put it in the clay gun with a rectangular end piece. You will obtain a long strip (you can also do it without the clay gun).

61817340

Cut the strip and texture it as you prefer: here I used a piece of net.

61817447
Cut the edges to obtain a 1 cm. strip, for 20 cm length.

Cut 4 strips 3-4 cm long, which more or less corresponds to the perimeter of the paper ball.

In the rest of the clay, cut also 2 rounds 1 cm. diameter (I've used a kemper cut).

Cover the strips with a golden pearl-ex, leaving 5 mm on each side without powder in order to let the strips adhere on the circles.

61880957

Place the strips to form a cross, with the textured face downwards. Let it adhere without pressing too much.


61881038

Turn it over ant texture the circle. Put some pearl-ex on it.

Turn it over again and place the paper ball in the middle, and pull up the strips on it. Correct the length of the strips to obtain this:

61881055

(normally, you would not have pearl-ex on the strips on top, where the circle will be placed)

On top you will dig a little with the help of the head of a pin the middle of the circle to place a little bead, fixing it with some liquid fimo.

(Here I put some pearlex before, but you can put it very well after the cage is mounted)

61819017

Bake following the instructions.

After baking, plunge it some time in the water, but not too much because the paper is not too much thick.

with a tweezer or a crochet you will take away the paper with delicacy:

61819155

And you have the bead in a cage! You will only have to sand the edges and varnish:

61819253

This model is not so refined, because the interior bead is not well-matched to the cage.
Another example :
61882191

Posté par chiocciolazzurra à 07:00 - - Commentaires [14] - Permalien [#]
Tags :


lundi 24 octobre 2011

Jade Imitation Tutorial

jadeitejadejadeiteajadeiteb_d1

 This is a recipe for creating a faux jade with polymer clay. Its inventiveness resides in the fact that we can find all the components in France. for the rest, it is a mix and match of other techniques.

 

jade1

You will need:

- some translucent Sculpey clay

- some acrylic inks (here Magic Color blue and earth brown)

- Optional: a little bit of green polymer clay (here some Granitex)

jade2

Divide the translucent clay bar into four equal parts, soften it and flatten it.

 

jade3

Leave aside a quarter of translucent clay, and colour the other three with different quantities of acrylic inks, in order to obtain 3 shades of olive green. Let them dry for 15 minutes.

 

jade4jade5

Pass each strip of clay through the pasta machine in order to mix the colours and obtain a homogeneous shade. The Sculpey clay is quite adhesive, so after a while you will need a pause, otherwise it will attach to the pasta machine (see right picture).

 

jade6 jade7

You will obtain three logs of shading green and a log of translucent.

 

jade8 jade9

You will put them all together, and you will add, if you wish, the little bit of green clay. Twost them together in order to obtain a log roughly marbled. Form a lump.

 

jade_10

Stretch the lump in order to detach some portions, repete this operation several times, and gather the detached pieces each time on the lump. With some experience, you will know when to stop this operation.

 

jade_11

Here you are, your faux jade clay is ready. You will take the amount you need and

 

jade_12

pass it one or two times through the largest setting of the pasta machine.

 

jade_13

On the left, you have a sample with Fimo, on the right with Sculpey.

For the cooking: between 110 and 115 °C for 20 minutes. You will have to keep an eye on the cooking. When the colour is the right for you, you will plunge the object into some ice-cold water. Be careful: the clay will still darken when you pull it out from the oven, so do not keep too long into it.

 

jade_14

Yves

---------------------------
you will find other recipes in English:

here
here  and here


This tutorial with images is an intellectual property of its author.
Please, respect his/her work and do not copy / reproduce / translate it without his/her authorization.


 

Posté par chiocciolazzurra à 08:00 - - Commentaires [5] - Permalien [#]
Tags :

mercredi 10 août 2011

Circus Beads

edited on 30 mai 2011

because many people didn't understand the reduction and the cutting of the cane, two pictures have been added to Kelly's tutorial by

skwizzscreation

64258305

 You need to make a skinner blend with at least three colours.

Then, you join a white and a dark coloured strip of clay, here a blue one.

reduction

you wrap the strip obtained into a jellyroll cane.

you reduce the cane obtained into a long log and you use a rippled tissue blade to cut slices into the log on the length sense

decoupage

64258405

 when you cut slices into the log, you see that pretty patterns will appear: you will use these slices to cover a ball of clay, taking care of smoothing very well the joint.

As a final step, you will create the beads you prefer in the shapes you prefer, taking care of not crushing the sides.

This is your turn to play!!!

64258429

64258505

Translated by Maria: chiocciolazzurra@yahoo.it

This tutorial with images is an intellectual property of its author.
Please, respect his/her work and do not copy / reproduce / translate it without his/her authorization.

Version française ici

Posté par chiocciolazzurra à 07:27 - - Commentaires [7] - Permalien [#]
Tags :

lundi 16 mai 2011

mother-of-pearl according to Hélène

version française

20_02_11_01

 TUTORIAL FOR IMITATING MOTHER-OF-PEARL

I take one part of translucent Fimo for each two of mother-of-pearl Fimo. Your recipe can surely be modified according to your taste. I think that using only mother-of-pearl will obtain as a result too brilliant, too artificial. But, as always, it is only a matter of taste...

01_Tuto_Nacre

I start by conditioning the clays with the pasta machine and I mix the two of them.

Then I choose some mica powders in different colours: here blue, red and mother-of-pearl.

02_Tuto_Nacre

with a brush, I put some mica powder on the mix of clys, passed through the pasta machine set nr. 1.

03_Tuto_Nacre

Here, I finish this job with a generous layer of pearly white: I need to point out this because in the picture it is not visible.

Then I fold the sheet in two, with the mica powders on the inside face.

04_Tuto_Nacre

I pass this folded sheet on the pasta machine at least 15 times, re-folding it each time in the same sense, as you do with a skinner blend.

05_Tuto_Nacre

Then I refine the sheet, passing it progressively from nr. 1 to nr. 6 on the pasta machine.

06_Tuto_Nacre

After that, I fold into an accordeon the sheet obtained. I try to reduce this packet of clay toward the center, to constitute a block of clay with some creases.

07_Tuto_Nacre

I pass the roller to smooth the stock and then I start to cut layers of clay not too thin: the objective is to reconstitute later a sheet of clay directly workable. 

08_Tuto_Nacre

Reconstitute a sheet of clay with the slices you have prepared

09_Tuto_Nacre

10_Tuto_Nacre

Then you pass the roller very well in order to smooth the sheet, you pass it though the pasta machine nr. 1 without stretching it too much. And now your plate is ready for u se.

11_Tuto_Nacre

My advice: I prefer to sand and polish and not to apply varnish, becaus ethe effect is more realistic. Anyway, if you wish to have more brightness, you can apply, ON THE RAW CLAY NOT COOKED, apply at the last moment a stroke of pearly mica powder. Once passed in the oven, you need to varnish your piece of work made with this technique (it will be more brilliant but less natural, in my opinion).
 
Cheers! Hélène.

Posté par chiocciolazzurra à 10:36 - - Commentaires [15] - Permalien [#]
Tags :

samedi 26 mars 2011

Tutorial for extruded whirlwinds

When I hear about whirlwinds, it reminds me always to that Jeanne Moreau song, "le tourbillon de la vie". It is a melody you can sing all day long (and indeed I hope that when you'll click on the link above, you'll be singing a whole week ;-p)

By chance, the first verse speaks about the subject we are interested in: the jewellery.

"Elle avait des bagues à chaque doigt,

Des tas de bracelets autour des poignets,

Et puis elle chantait avec une voix

Qui, sitôt, m'enjôla."

Myriam, very kind of her, has got a tutorial to share with us, to create some almost-mesmerizing beads: this way, she will not be alone anymore in her whirlwind.

L_atelier_de_lune__2_

L_atelier_de_lune__3_

L_atelier_de_lune__1_

 

Are you ready? Take you clay-guns!

First of all, roll some sheets of clay in different colours at the thickest setting of the pasta machine (nr. 1 in my case). Generally,I make spiral beads with 5 contrasting colours.

1

Then, prepare your clay gun with the 7 hole extruder.

2

Cut some round pieces with a round shape cutter the same size of the extruder.

3

Pile up, random or as you prefere, 14 to 16 round pieces.

4

With your hans, smooth and extend a little this stack of round pieces, in order to introduce into the clay gun.

Pay attention: the first colour will be the prevailing one of the spiral bead.

5

You will obtain 7 threads. Here we have 14 threads: the firft 7 with the orange colour and the other 7 with a prevailing brown.

6

On a sheet of clay from a setting 1, wind the threads you have obtained and press it in order to avoid air bubbles.

7

Press delicately with a roller, taking care not to deform the spiral shape.

8

Pass the sheet with the spiral through the pasta machine, settin nr. 1. The spiral will result slightly deformed.

9

Pass again the sheet with the spiral through the pasta machine, settin nr. 2, by previously turning it in order to deform it in another direction: so it will regain the original shape.

10

Here the spirals are ready to be cooked on a escargot-dish!

11

 

Thank you very much indeed for sharing  this with us, Myriam. ;-)!

"On s'est connu, on s'est reconnu,

On s'est perdus de vue, on s'est r'perdus d'vue ..."

ps: to assemble the whirlwind beads you have this trick

Translated by Maria: chiocciolazzurra@yahoo.it

This tutorial with images is an intellectual property of its author.
Please, respect his/her work and do not copy / reproduce / translate it without his/her authorization.

version française ici

Posté par chiocciolazzurra à 07:00 - - Commentaires [7] - Permalien [#]
Tags :


samedi 11 décembre 2010

Lentil beads without holes

by Myriam

The following are the explanations to assemble lentil beads without making holes into them. I'd like to thank again Legna for having given to me some piece of information.

110

When you have baked and polished your lentils, prepare 2 sheets of clay, the first at the number 2 of the pasta machine, the other at number 3
You make a round shape into the nr 3 sheet, with the round cutter you have used to make lentils
Into the nr 2 sheet, you make a round shape slightly smaller

turn over the lentil

210

Put the bigger round onto the inside of the lentil and press very well in order to avoid bubbles

310

Cut the surplus with a blade and smooth the edges with your fingers

410

Place a metal rod at 10:10 (or at the middle if you are doing a bracelet)

510

Then cover the rod with the smaller round and press strongly

612

Cut the surplus and smooth

710

And this is it! You only need to re-bake the lentil with the rod within it.

This tutorial with images is an intellectual property of its author.
Please, respect his/her work and do not copy / reproduce / translate it without his/her authorization.

Translated by Maria: chiocciolazzurra@yahoo.it

En français ici

Posté par chiocciolazzurra à 08:50 - - Commentaires [2] - Permalien [#]
Tags :

samedi 16 octobre 2010

Fimo Threads

by Moïse

artisan_bijoutier_createur

This technique was born by chance: I was crafting a piece of jewelry made of translucent plates and I realized that fimo blocks remain slightly flexible after the cooking. Hence the idea of trying with threads, so I made researches in order to increase both the flexibility and the strength.

This is the fruit of my efforts and researches:

In order to realize colored flexible threads which are practically unbreakable you will need:

Some translucent fimo clay (with or without a color)

Some liquid fimo

Some soft fimo clay in different colors

Some pearl-ex in different colors

Some glittery in different colors

A clay gun and some white paper (for the cooking)

artisan_bijoutier_createur0


The technique :

There are different ways of proceeding, but the basic ingredient is the translucent fimo clay: the others (liquid fimo, pearl-ex, glitters and fimo soft) are meant only to soften and color it.

Basic technique:

Make some threads with one of the 7 translucent effects fimo clays (you can also mix them in order to obtain other colors) and cook them at the lowest degree suggested. You will already obtain a good result but next technique is definitely better.

Advanced technique:

Take one part of translucent flesh-colored fimo (014), the amount necessary  to your needs (you can also use another color).

Pour colorer le transparent on ajoute une petite quantité (maximum 5 %) de pâte soft colorée ou un soupçon de perlex ou bien un peu de poudre pailletée (suivant l’effet désiré, on peut associer les différents ingrédients dans un même mélange ).

In order to color the translucent clay you can add a little bit (max 5%) of colored clay or just a pinch of pearl-ex or some glittery powder (according with the effect you wannt to obtain, you can also mix different ingredients in the same blending)

artisan_bijoutier_createur

You mix in order to obtain a homogeneous clay (pay attention not to form any bubble):

artisan_bijoutier_createur1

You add to the mix you have obtained a little bit of liquid fimo and you mix again (it will be sticky, as the scrap clay). The liquid fimo will increase the flexibility and the resistance:

artisan_bijoutier_createur2

You put the clay you have obtained into the extruder, and you will make some spaghetti threads (you can use different diameters and different shapes, but you need to know that the thicker the thread the less flexxible will be the result, and viceversa):

artisan_bijoutier_createur3

Once the spaghettis are done, you will bake them: you put them onto a white sheet, being careful not to superpose them. You can also use an accordion sheet as in the picture:

artisan_bijoutier_createur4
artisan_bijoutier_createur5

For the baking: you start with a cold oven and you gradually arrive to 110°. Then you keep the oven at 110° for 30 minutes. When you put out the threads of the oven you plunge them into the cold water:

artisan_bijoutier_createur6

This is it: after the baking, you must be able to make a knot with the threads:

artisan_bijoutier_createur7

If, after the baking, your threads are breaking:

Either you haven't respected the baking mode

Or you have put too much colouring devices into your clay at the beginning (fimo soft, glitters, pearl-ex)

Or you have put too much liquid fimo

Or you have left air bubbles in the mix

I hope this tutorial will help you and will guide you towards new creative horizons.

Have a nice work and havefun!

This tutorial with images is an intellectual property of its author.
Please, respect his/her work and do not copy / reproduce / translate it without his/her authorization.

Translated by Maria: chiocciolazzurra@yahoo.it

En français ici

Posté par chiocciolazzurra à 08:33 - - Commentaires [6] - Permalien [#]
Tags :

lundi 8 décembre 2008

Tutorial Matisse cane

en français ici

there was a challenge in our polymer clay group about the theme "Matisse and the polymer clay artists". I chose one painting from this artist which was good to reproduce in a cane. These are the steps to make it.

and this is the model:

fd_030105_matisse2

CIMG5199

    1 ) make 12 white logs          

CIMG5200

       2) give them the shape of petals

CIMG5202

3) make a black log to form the center of the flower   

CIMG5212

       4) and 12 little black strips

     CIMG5213      

   5) arrange the petals around the center, by putting the black strips between them      

CIMG5214

                  6) cut 12 little black sticks

CIMG5215

    7) arrange them to fill the gaps between the petals            

CIMG5216

     8) wrap the big log with a black sheet of clay

CIMG5217

        9) reduce the cane and cut it in two   

CIMG5210

    10 ) prepare 6 green logs

CIMG5211

      11) cut them in two         

CIMG5219

           12) arrange them around the flower cane

CIMG5221

    13) insert some black triangles between each green log 

CIMG5218

14) wrap this big log with a black sheet of clay

CIMG5233

15) and this is the first flower

CIMG5225

16) you make the same with some blue clay and the other log

CIMG5222

18) prepare a yellow log, a fuchsia one and a light pink one with a strip of black clay around       

CIMG5223

                19)  reduce these logs and cut them into two (into 4 the light pink one)   

CIMG5228

                  20) place the two yellow logs one next to the other and fill the gaps with black triangles

CIMG5229

                 21) place the fuchsia logs.....    

CIMG5231

                  22)....and the light pink ones as in the picture and fill all the gaps with triangles and strips of black clay

 CIMG5232   

23 ) this is the result

CIMG5235

                 24) reduce the canes (the yellow and rose one must be in a square shape)                  

CIMG5238

  25) and place them as in the picture

CIMG5239

26 ) wrap this big log with a black sheet of clay

CIMG5241

and this is it!

fd_030105_matisse2

FLOFIMO


Translated by Maria: chiocciolazzurra@yahoo.it

 

This tutorial with images is an intellectual property of its author.

Please, respect his/her work and do not copy / reproduce / translate it without his/her authorization.

 

Posté par chiocciolazzurra à 11:06 - - Commentaires [12] - Permalien [#]
Tags : ,

mercredi 19 novembre 2008

A technique to make multicoloured tube beads

I love so much those african beads, and so I've managed to make the same with Fimo clay! There are several techniques, and this is mine!

1/ first, you make a coloured cane (preferably a millefiori one), you cut it into slices and you prepare a sheet by putting the slices one beside the other.

IMG_2860

2/ put your plate between two sheets of greased paper (to avoid it sticks to the working place) and flatten it in order to blend the slices together.

IMG_2861

3/ when you have flattened the plate, cut the edges and with the scrap you prepare a little log which will be the center of the beads. Put this log on the plate and roll  to put around it the coloured sheet. Then cut and adjust the bead.

IMG_2864

IMG_2867

IMG_2869

4/ bake the beads as usual. Personally, I make the holes after baking.

Have a nice time!!

Vivi (fimo de Vivi)

IMG_2920

Translated by Maria: chiocciolazzurra@yahoo.it

This tutorial with images is an intellectual property of its author.
Please, respect his/her work and do not copy / reproduce / translate it without his/her authorization.

Posté par chiocciolazzurra à 07:26 - - Commentaires [6] - Permalien [#]
Tags : ,

mercredi 1 octobre 2008

again... but we never get enough!

Tutorial flower cane by  Sabine

en français ici

tutosabun

1 - Make a skinner blend with three assorted colours (at least half a pack of each), then pass it in the pasta machine at the thinnest grade (#1)(from the clearer to the darkest side, in order to avoid bad smears); 2 - fold this sheet as in photo nr. 3; 3 - make a thin sheet with black clay and wrap it around the log, then cut it into 4 equal parts

tutosabdeux

4 - take two pieces and round them from one side (ph. 6); 5 - with a cylinder-shaped object (as a pen) press within the darker sides in order to put a pistil between them (ph. 7); 6 - to make the pistil make a little red log with a thin black sheet around, and again a red one; 7 - Under the pistil, put a thin sheet of red clay covering less then half log and a serpentine of the same colour as in photo n. 10; 8 - take the two remaining blocks and stretch them, pinch the two sides and put them around the heart of the flower as in ph. 11 and 12; 9 - reduce this log in a long one of 16 cm. and cut it into eight pieces of 2 cm (ph. 13-14); 10 - the petals are thus ready by pinching each of the 8 pieces on their sides (ph. 15). start to assemble them together leaving a hole at the center (ph. 16), adjusting their thickness in order to have a proper measure to form the heart later. As a variation, you can make a flower with six petals.

tutosabtrois

11 - let's make the heart of the flower. to do this, make a little log of black clay (quite thick) and wrap it on half side  with a thin sheet of red (ph. 17). Reduce it in order to obtain a 20 cm. long log for a 5 mm. diameter. 12 - pinch the red side of this long long as in photo 18, then cut it into 10 pieces and put them close one to the other on the larger side to form a round log(ph. 19). 13 - wrap this log with a sheet of red clay (ph. 20).  14 - reduce this log to the proper size and put it at the center of the flower (ph. 21). 14 - place between the petals some translucent clay to fill the spaces, reduce the cane  and the game is done!

Translated by Maria: chiocciolazzurra@yahoo.it

This tutorial with images is an intellectual property of its author.
Please, respect his/her work and do not copy / reproduce / translate it without his/her authorization.

Posté par chiocciolazzurra à 07:00 - - Commentaires [13] - Permalien [#]
Tags : , ,